Plumber's Essentials: Your Key to Installing a Bathtub
CallAlmost everyone has their unique theory on the subject of Installing A Bathtub.
Setting up a bath tub isn't precisely brain surgery, yet it does need strong plumbing, woodworking, as well as sometimes, tiling abilities. Replacing an old tub with a brand-new one is likewise a moderately challenging task. If the old tub is easily obtainable, the job can move easily; if you have to open a wall surface to eliminate the old tub and position the new tub, the task is a lot harder. In either situation, the project is within a house handyman's skills, although you will need a helper to move out the old tub and embeded in the new one. Make certain you have actually qualified yourself for the work as well as fit attempting it. As opposed to hiring a specialist to take over a halfway-completed job, it is much better to take into consideration using one before you begin. Chances are you may need an expert plumber to make tube links.
This short article will aid you set up a brand-new bath tub in your shower room if you have actually already gotten a brand-new tub and also don't need to change the setup of your previous water system pipes.
Your devices as well as material list ought to comprise the following:
Preparing for the Setup
To start with, the supporting frame supplied with the bathroom needs to be fitted (if needed) according to the manufacturer's instructions. Next, fit the taps or mixer to the bath tub. When fitting the tap block, it is necessary to see to it that if the faucet features a plastic washer, it is fitted between the bathroom and the taps. On a plastic bathroom, it is additionally sensible to fit a sustaining plate under the taps device to avoid stress on the bathtub.
Fit the versatile tap connectors to the bottom of both taps making use of 2 nuts as well as olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet through the hole in the bath. Make use of the nut provided by the supplier to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bath. Ensure you use all of the provided washers.
Connect the trap to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom need to now be ready to be fitted in its last position.
Removing Old Taps
If you need to replace old taps with brand-new ones as a part of your installment, then the first thing you should do is separate the water supply. After doing so, activate the faucets to drain pipes any kind of water remaining in the system. The procedure of getting rid of the existing taps can be quite troublesome as a result of the limited access that is commonly the instance.
Make use of a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipelines to the faucets. Have a cloth ready for the remaining water that will originate from the pipelines. When the supply pipes have actually been gotten rid of, make use of the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary faucets from transforming during this procedure. Once the faucets have been gotten rid of, the holes in the bath/basin will have to be cleansed of any old securing compound.
Prior to proceeding to fit the new faucets, compare the pipeline connections on the old faucets to the brand-new taps. If the old faucets are longer than the new taps, after that a shank adapter is required for the new faucets to fit.
Setting up the Tub
Making use of both wood boards under its feet, put the bathtub in the called for position. The wooden boards are helpful in evenly spreading the weight of the bathtub over the area of the boards instead of focusing all the weight onto four small points.
The next objective is to ensure that the bathtub is leveled all round. This can be achieved by inspecting the spirit level and adjusting the feet on the bathtub up until the level reads degree.
To install faucets, fit all-time low of the outermost adaptable tap port to the ideal supply pipeline by making a compression join; after that do the very same for the various other tap.
Turn on the water system and also inspect all joints and brand-new pipework for leakages as well as tighten them if necessary. Fill up the bathtub as well as additionally examine the overflow electrical outlet as well as the typical outlet for leaks.
Finally, take care of the bathroom paneling as described in the supplier's user's manual. Tiling and also securing around the tub ought to wait until the tub has been made use of a minimum of when as this will certainly settle it into its final position.
Suitable New Taps
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic adapter to prevent damages to the string. One end of the port fits on the plastic tail of the tap as well as the various other end provides a connection to the existent supply pipes.
If you need to fit a monobloc, then you will certainly call for decreasing couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next, position the tap in the installing opening in the bath/basin making sure that the washers remain in location between the faucet and the sink. Safeguard the tap in position with the producer given backnut. When the faucet is securely in position, the supply pipelines can be linked to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with typical faucet adapters. The former type needs to be connected to the tap finishes initially, tightening up just by hand. The supply pipes can later be connected to the various other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Tub
In the location where the bathroom satisfies the floor tile, it is required to secure the joins with a silicone rubber caulking. This is essential as the fitting can relocate sufficient to split an inflexible seal, creating the water to pass through the wall surface in between the bath as well as the tiling, bring about difficulties with wetness and also possible leaks to the ceiling listed below.
You can pick from a range of coloured sealants to assimilate your fixtures and installations. They are offered in tubes and cartridges, as well as are capable of securing gaps approximately a width of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with spins of soaked paper or soft rope. Remember to always load the tub with water prior to sealing, to enable the activity experienced when the tub is in usage. The sealant can fracture fairly very early if you do not take into account this motion prior to securing.
Conversely, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are additionally conveniently readily available on the market. It is suggested to fit the tiles using waterproof or waterproof adhesive and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
:max_bytes(150000):strip_icc()/convert-tub-to-shower-4156975-05-db9a69eb718545759045e6e39b4cfacf.jpg)
I ran across that blog posting on Installing A Bathtub when perusing the web. Do you know anybody else who is intrigued by the subject? Why not promote it. I cherish reading our article about Tools You Need to Install a New Bathtub .
Certified solutions offered.